Chaney Instrument Thermometer 3166 User Manual

03166 INST 012206  
03166 Wireless Digital Cooking Thermometer  
Meat-taste temperature Quick Reference  
TEMPERATURE  
PROBE  
WELL-DONE  
170º  
MEDIUM  
160º  
MED.-RARE  
145º  
RARE  
140º  
BEEF  
GROUND BEEF  
VEAL  
POWER  
OFF/ON  
ALARM  
OFF/ON  
ALARM  
OFF/ON  
POWER  
OFF/ON  
COOK  
160º  
170º  
170º  
170º  
180º  
180º  
N/A  
160º  
160º  
160º  
N/A  
N/A  
145º  
145º  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
SET  
ON  
TIMER  
THERMO  
F
W
IR  
E
L
E
S
S
LAMB  
W
I
R
E
L
E
S
S
OFF  
PORK  
START/  
STOP  
HR  
MIN  
CHICKEN  
TURKEY  
N/A  
MODE  
N/A  
N/A  
WIRELESSPAGER  
BASEUNIT  
Do not return product to retail store.  
INCLUDED IN THIS PACKAGE:  
(1) Digital cooking thermometer base unit  
(1) Digital cooking thermometer wireless pager  
(1) 3 foot wire and thermometer probe  
For Technical Assistance and product return information,  
please call Chaney Instrument Co. direct at:  
877-221-1252  
Thank you for purchasing this Acu-Rite Wireless Digital Cooking  
Thermometer. Please read all instructions prior to using this  
instrument.  
Features  
• 3-line LCD shows cook temperature, set temperature and timer  
for BBQ or Oven cooking.  
• Programmable temperature alert  
• High-temp stainless steel temperature probe with 3 foot cable  
• Wireless pager alerts you of temperature  
4
1
Battery Installation  
Low Battery  
Both the base unit and the wireless pager have low battery icons  
that will display on the LCD if the battery is getting low.  
Install 2 alkaline AAA(1.5v) batteries (not included) into both the  
base unit and into the wireless pager. Slide the power switches on  
both units to the “ON” position to activate each unit.  
WIRELESS PAGER  
Wireless Pager Alerts  
The base station will alert the pager when the target temperature is  
reached or when the timer on the base station reaches “0:00.” To  
receive wireless data and alerts, be sure the pager is powered on  
and that the alarm switch is activated.  
BASE UNIT  
Setting the clock and thermometer  
To set the clock to the correct time, first press the “MODE” button  
to enter into clock display mode. Next, hold the “MODE” button  
down until the time display begins to flash; then you may adjust the  
time using the “+HR” and “-MIN” buttons. Press the “MODE” button  
to confirm your time setting.  
The wireless pager receives data from the base station unit and  
alerts you when the base stations’ temperature probe reaches a  
certain pre-determined number. The pager also alerts you when the  
base stations’ timer reaches “0:00.” The wireless pager also has a  
built-in timer that can be used independently from the wireless  
base-station.  
At this point you may select between 12 and 24 hour time formats  
by pressing the “HR” button. Then you may also choose ºC or ºF  
temperature display mode by pressing the “-MIN” button. To exit  
set-up mode and confirm your settings, press the “MODE” button.  
The wireless thermometer system has a range of 100 feet, which  
can be affected by electronic interference and certain building and  
housing materials. When the pager cannot receive the signal from  
the base station for whatever reason, the pager will read “OUT OF  
RANGE” on the display and will beep.  
Setting the target temperature  
To set the target temperature, first press the “MODE” button until  
the time/clock is displayed. Press the “+HR” and “-MIN” buttons to  
set the target temperature. Slide the “alarm on/off” switch to “on”  
and the alarm will sound when the actual temperature reaches the  
target temperature.  
Wireless Pager Backlight  
The wireless pager has a built-in backlight for easy viewing. To  
activate the backlight for 4 seconds, press any button on the front  
of the pager.  
Setting the timer  
To set the timer, first press the “MODE” button to select TIMER.  
Press the “+HR” and “-MIN” to adjust the timer to the desired  
countdown time. Then press “START/STOP” to start and stop the  
timer. To reset the count, stop the timer first and press “+HR” and  
“-MIN” together at the same time. Slide the “alarm on/off” switch to  
“on” and the alarm will sound when the timer countdown reaches  
“0:00”.  
Setting the pager timer  
To set the timer, first press the “MODE” button to select TIMER.  
Press the “+HR” and “-MIN” to adjust the timer to the desired  
countdown time. Then press “START/STOP” to start and stop the  
timer. To reset the count, stop the timer first and press “+HR” and  
“-MIN” together at the same time. Slide the “alarm on/off” switch to  
“on” and the alarm will sound when the timer countdown reaches  
“0:00”. NOTE: both the base unit and the wireless pager must  
be powered on and in range for the independent pager timer to  
work properly.  
Wireless Pager Alerts  
The base station will alert the pager when the target temperature is  
reached or when the the timer on the base station reaches “0:00.”  
To receive wireless data and alerts, be sure the pager is powered on  
and that the alarm is activated.  
 
2
3

Blue Microphones MP3 Player Mikey User Manual
Bosch Appliances Oven HBA738550 User Manual
Boss Audio Systems Stereo Amplifier MC300 User Manual
Braun Electric Shaver 340s 4 User Manual
Brother Sewing Machine Innov is 30 User Manual
Bushnell Binoculars 260140 User Manual
Canon Camcorder ZR200 User Manual
Canon Digital Camera SX410ISBLACK User Manual
Casio Printer IT 3100 User Manual
Casio Printer KL 70E User Manual